No products in the cart.
Store as far away from humidity as possible - use the far corner of the boathouse
Always have a gasket. Re-attach with E6000 adhesive. Contact us for replacements and we'll send them.
Before leaving the boathouse for a row, turn the light on (snugly) and don't open the lid until returning to the house.
At least 8 hours
It's always good to drain battery completely throughout the season from time to time
It is not necessary to charge after every use
Delivery is subject to our availability. We receive containers from England 3 or 4 times a year.
Dry the board using a soft cloth, use rice to absorb remaining moisture, do not use heat
Check out this video on the suction cup from Adams Manufacturing.
Bloated, peeling
Mail circuit board - remove from enclosure. Do NOT send the enclosure
Enclose your name, contact information and return address
To turn your Beacon on, twist the cap closed. Then snug the cap even more to create a more watertight seal.
We suggest that you turn the lights on BEFORE leaving the boathouse or rack. Keep them on until you return. This helps prevents moisture from getting inside the light.
When finished using your Beacon unscrew the cap and make certain that the circuit board inside the light has not gotten wet.
If water should get into your Beacon, even just a little! remove the cap, carefully slide the light board out of the enclosure and dry everything off. Once all parts are dry, reassemble and you should be good to go.
Never use the lights if the gasket is missing from the lid.
Beacon Lights will float, when the screw cap is CLOSED TIGHTLY.
To charge your Beacon, remove the lid completely. Attach the USB cable to the socket at the top of the circuit board and plug the other end of the cord into the wall charger. Plug the charger into any electrical outlet. You can also charge from the USB port on any computer and car charger with a USB port.
The yellow charging LED will light while charging and go out when charging is complete. One full charge will easily last several practices.
TO A BOW NUMBER CLIP
Slide the fin of the Beacon enclosure into your bow number clip, just as you would a racing bow number. If your bow number holder has a hole in it you can further secure your Beacon using a #10x3/4” machine screw and a lock nut, a clevis pin, or other locking pin type hardware.
USING A SUCTION CUP ATTACHMENT
Make sure the boat deck is clean and smooth. Dirt, dust, scratches in the paint or uneven deck repairs may prevent good suction between the deck and suction cup.Wipe the suction cup with a damp cloth to clean and slightly moisten the surface that will contact the boat. . Loop the safety lanyard through the “flag loop” on the end of your boat (if there is one) or around the steering yoke post just in case the suction cup releases.
ATTACHING A ROWKRAFT LIGHT KEEPER
For an attachment that’s more permanent than the suction cup to the boat’s deck, use the optional Light Keeper which attaches using very strong waterproof double sided tape. Peel the protective strip off of the tape on the Light Keeper and press firmly onto the boat’s deck. (You can also add your own screws if you really want to be sure it won’t fall off).
Tom recommends using CorrosionX to clean the boards. Dielectric grease can be used on both socket and cord ends to keep contacts in good shape after cleaning.
No need to discharge
Send questionable boards back to us for assessment
Don't store in plastic
Charge fully
Discharge fully
Recharge
8 Tips on Using Suction Cups:
The care and use of suction cups is very simple:
Make sure the suction cup is clean and free from debris.
If the suction cup needs to be cleaned, wash in warm soapy water then dry gently with a lint-free cloth.
Clean the surface you are applying the suction cup to. It won’t adhere well to a dirty surface.
To enhance suction, a tiny dab of Vaseline or cooking oil may be rubbed on the rim of the cup.
Press the cup all the way down, against the surface.
The suction cup may need to be “burped” periodically by pressing down on it to remove any air that may have seeped in.
Temperature and humidity variations may make a suction cup lose its grip. If bonded above 40⁰ F/5⁰ C the cup will provide the most reliable service from -22⁰ to 120⁰ F.
To remove the cup, simply pull up on the release tab to break the suction.
Charging station examples
Check charging cord and plug.
BEACON WARRANTY
RowKraft Products LLC warrants your KraftLight Beacon to be free from defects in material or workmanship for one year from the original date of purchase. During this period, RowKraft will repair or replace, at no charge, products or parts of the Beacon that prove defective under normal use and maintenance.
This warranty covers defects in manufacturing discovered while using the product as recommended. The warranty does not cover any problem that is caused by conditions, malfunctions or damages not resulting from defects in material or workmanship. The warranty does not cover parts that are subject to normal wear and tear, breakage due to improper use, theft or loss.
To obtain service under this warranty, please contact RowKraft at [email protected] or write to RowKraft Products, 1500 Longshore Drive, Ann Arbor, MI, 48105.
The catamarans have been specifically designed to produce minimal wash.
The RS CAT16 9.9hp 4-stroke with 12-litre fuel tank will last between 120 and 160 km.
The RS CAT16 15hp-20hp 4-stroke with 12-litre fuel tank will last between 100 and 140km.
The RS CAT16 with 9.9hp top speed is 28kph
RS CAT16 with 15Hp top speed is 32kph
The RS CAT16 with 15hp is designed to carry 4 persons. However, because it has a buoyancy capacity of 650kg, it will carry significantly more for emergency rescue purposes only.
Delivery is subject to our availability. We receive containers from England 3 or 4 times a year.
Yes. We’d be happy to arrange a test drive with us or find a launch that’s already working in your area.
With trailer/trolley: 1-2 persons. Without trailer/trolley: 4-6 persons.
RS CAT16 complete with a 15Hp about 500 pounds
The RS CAT16 has a 4-metre (14-feet) turning circle.
Yes, easily! The catamaran and trailer are very light, less than 1100 pounds with motor and trailer.
We supply trailers customised for towing as well as launching the catamarans in and out of the water. The trailers and trolleys are easily operated by one person.
Stronger construction and built to last – first boats ever sold in 1992 are still in use!
Higher speeds achieved with less horse-power.
Manoeuvrability – tight turning circle of 4 metres (14-feet radius).
Low wash because of less water displacement with twin hydrodynamic hulls.
Lower energy consumption.
More economic to run because of fuel efficiency.
The hulls are made of extremely hardwearing roto-moulded, TRILAM polyethylene, which is approximately 10mm to 12mm thick. The first catamarans were built in 1992 and are still in active use!
All our catamarans carry a 10-year limited warranty on the hulls.(Please see T&C)
Email us for a current quote! Prices vary slightly from shipment to shipment but they’re always the most affordable launch of its type.
Add items to your cart
Go to your cart
At the end of your Billing contact information, there's a check-box for "Create an account?"
Check that box
Upon a successful checkout, you'll create an account with RowKraft!
Enter your registered email.
Follow the instructions sent to your email.
Add items to your cart.
Go to the 'Checkout' page.
Find the 'Apply Discount Code' section.
Enter code and click 'Apply'.
Credit/Debit Cards.
ACH Bank Transfer
Yes. We use SSL encryption and other security measures to protect your data, and no Credit Card or Banking Information is stored on our systems.
We try to ship all orders within 3 days but during our busy seasons it may take longer.
Yes. See our 'Shipping Policy' for details.
Go to 'My Account'.
Click on 'Addresses'.
Update your details and save.
